Welcome to The Vintage Car!

We have discussions on Tools,
Garages, Cars and Vintage Paxton's Glass bead cabinet dust collection system - The Vintage Car - The Vintage Car
Welcome to The Vintage Car - The Hot Rod, RatRod, Muscle Car, Street Rod & Classic Car Information Portal
tvcHeader1tvcHeader2tvcHeader3tvcHeader4tvcHeader5header6tvcHeader7
Article by Todd Wallace    (09-18-09 07:02 AM)
/forums/skins/cobalt/indicators/attach.png
 
You will need;

•1 shop vac (the small $20-30 (1 gallon size works fine)
•1 empty 5 gallon spackle bucket with tight fitting lid.
•3' (min) of 3/4 or 1" ID rubber or vinyl hose.
•2 each, 3/4 or 1" (see hose size) PVC ribbed couplings.
Drill 2 holes in the bucket lid to fit the ribbed couplings, if they are not real tight, caulk or seal them where they go thru the lid. Cut a length of hose to fit 3/4 of the way into the bucket. Cut a short one inch piece of hose for the inside of the other fitting, angle it towards the side or make a splash diverter so to keep the water out of the short hose. Insert a length of rubber hose to your blast cabinet where the shop vac is supposed to hook into or make a hole in the cabinet for the hose. Run the other end of this hose to the bucket fitting with the long hose inside. Hook up the shop vac to the fitting with the short hose. Fill the bucket 1/2 full with water or an anti freeze solution (in cold climates) When the vac is turned on it will create a suction in the water filled bucket, dust from the blast cabinet will be drawn into the water. No dust gets into the shop vac. So far it works great for me. Some playing around with the exact water level so it does not wet the vac filter was needed or a foam filter would work too. Be sure to use a wet/dry vacuum for this project. K-mart has/had the 1 gallon shop vacs for around $20, the fittings are PVC and I picked up a 4' of 3/4" ID vinyl hose.

The whole project cost less then $30. (but I had the vac for a year or so) If you saw the dust and dirt around my blast cabinet, you would know why I did this. If I used the shop vac directly, the filter clogged in 5 minutes so I just gave up until now. I don't want to dust up my new garage, at least not yet anyway. Foreseeable problems..... As the dirt fills the bucket, the water level will rise. Water freezes in the cold so now a place for your used antifreeze Improvments...... As my buddy the plumber came in while we were "creating" this thing, he wants to add a drain and an automatic fill valve to the bucket. Of course this would make it completely automatic but it's not THAT hard to empty a bucket every couple months. Unless you mounted it up high in the lower portion of your garage and have the blast cabinet upstairs like I do.


-- Frank Clarici Toms River, NJ

Original Link

 
Username Comments
Todd Wallace 
Administrator
Posts: 258
Todd Wallace
Loc: Colleyville
Registered on 02-10-09
09-18-09 07:04 AM - Post#308    

    In response to Todd Wallace

Attachment: filter2.jpg (146.13 KB) 14137 View(s)


Attachment: filter1.jpg (244 KB) 14469 View(s)


reposting pic's..didn't see them..







 
Icon Legend Permissions Topic Options
Print Topic


63588 Views
FusionBB™ Version 3.0 RC2 | ©2003-2010 InteractivePHP, Inc.
Execution time: 0.06 seconds.   Total Queries: 37   Zlib Compression is on.
All times are (GMT -0600) Central. Current time is 03:55 AM
Top